Digitale Lehre
Digital teaching in SoSe 2020
The digital teaching in the subject "Design and Optimization of Vehicle Transmissions" takes place in the following free form:
The lecture recordings will be available weekly via the Moodle course. Please note the announcements in the Moodle course.
The schedule chain with the available room information in TUCaN represents the original presence planning and is to be ignored.
Digital teaching in SoSe 2020
The digital teaching in the subject "Design and Optimization of Vehicle Transmissions" takes place in the following free form:
The lecture recordings will be available weekly via the Moodle course. Please note the announcements in the Moodle course.
The schedule chain with the available room information in TUCaN represents the original presence planning and is to be ignored.
- Lehrende: Eckhard Kirchner
Semester: ST 2020
- Lehrende: Johannes Brötz
- Lehrende: Stefan Hackelbörger
- Lehrende: Katharina Henn
- Lehrende: Manuela Richter
- Lehrende: Philipp Wetterich
Semester: ST 2020
Digitale Lehre
The course Rechnergestützes Konstruieren (CAD) will be held as an [b]online teaching[/b] in SoSe 2020. The lecture will be digitally broadcasted and complemented by additional digital materials such as demonstrations and exercises.
The online teaching will start in week 17 ([b]from 20.04.2020[/b]) and will take place on the weekdays and times specified in the schedule (see TUCaN). The available room details for the individual dates in TUCaN represent the original attendance planning and will be replaced by the online teaching.
The technical access to the online teaching takes place via [b]Moodle[/b]. Here you will also find the link to the online broadcast before the lecture. You were automatically registered for the CAD Moodle course when you registered in TUCaN. If you have any problems with the Moodle course, please contact the supervising research assistants [b]Lennart Fischer[/b] or[b] Sven Winter.[/b] You will then receive all further information via Moodle.
As a [b]necessary requirement[/b] for the participation in exams, the software Siemens NX must be installed on your private computer. Instructions for installation can also be found under Moodle.
Lehrinhalte
The course provides an introduction to computer-aided design with 3D CAD systems and the CAD process chains based on them, in particular the process chain CAD - Technical Product Documentation. Starting with the product life cycle, the product development process is presented using modern methods of information technology. These include in particular CAD (Computer Aided Design) and PDM (Product Data Management). In the exercises accompanying the lectures, the lecture material is deepened and practically implemented on a modern 3D CAD system.
Literatur
The script for this class will be online at Moodle.
Important information and online tutorial:[url=https://moodle.tu-darmstadt.de/course/view.php?id=7103] https://moodle.tu-darmstadt.de/[/url]
Voraussetzungen
Registration from February 3th 2020, 10 AM, to March 27th 2020, 2 PM
Link: [url=https://www.iim.maschinenbau.tu-darmstadt.de/cad/cad_anmeldung/]IiM (http://www.iim.maschinenbau.tu-darmstadt.de).[/url]
Erwartete Teilnehmerzahl
550
Zusätzliche Informationen
ATTENTION:
Registration for the module, lecture and examination must be completed by 03.05.2020.
In TUCaN the registration or deregistration possibility for module, lecture and exam ends on 03.05.2020 23:59 o'clock.
Online-Angebote
[url=https://moodle.tu-darmstadt.de/course/view.php?id=7103]https://moodle.tu-darmstadt.de/[/url]
The course Rechnergestützes Konstruieren (CAD) will be held as an [b]online teaching[/b] in SoSe 2020. The lecture will be digitally broadcasted and complemented by additional digital materials such as demonstrations and exercises.
The online teaching will start in week 17 ([b]from 20.04.2020[/b]) and will take place on the weekdays and times specified in the schedule (see TUCaN). The available room details for the individual dates in TUCaN represent the original attendance planning and will be replaced by the online teaching.
The technical access to the online teaching takes place via [b]Moodle[/b]. Here you will also find the link to the online broadcast before the lecture. You were automatically registered for the CAD Moodle course when you registered in TUCaN. If you have any problems with the Moodle course, please contact the supervising research assistants [b]Lennart Fischer[/b] or[b] Sven Winter.[/b] You will then receive all further information via Moodle.
As a [b]necessary requirement[/b] for the participation in exams, the software Siemens NX must be installed on your private computer. Instructions for installation can also be found under Moodle.
Lehrinhalte
The course provides an introduction to computer-aided design with 3D CAD systems and the CAD process chains based on them, in particular the process chain CAD - Technical Product Documentation. Starting with the product life cycle, the product development process is presented using modern methods of information technology. These include in particular CAD (Computer Aided Design) and PDM (Product Data Management). In the exercises accompanying the lectures, the lecture material is deepened and practically implemented on a modern 3D CAD system.
Literatur
The script for this class will be online at Moodle.
Important information and online tutorial:[url=https://moodle.tu-darmstadt.de/course/view.php?id=7103] https://moodle.tu-darmstadt.de/[/url]
Voraussetzungen
Registration from February 3th 2020, 10 AM, to March 27th 2020, 2 PM
Link: [url=https://www.iim.maschinenbau.tu-darmstadt.de/cad/cad_anmeldung/]IiM (http://www.iim.maschinenbau.tu-darmstadt.de).[/url]
Erwartete Teilnehmerzahl
550
Zusätzliche Informationen
ATTENTION:
Registration for the module, lecture and examination must be completed by 03.05.2020.
In TUCaN the registration or deregistration possibility for module, lecture and exam ends on 03.05.2020 23:59 o'clock.
Online-Angebote
[url=https://moodle.tu-darmstadt.de/course/view.php?id=7103]https://moodle.tu-darmstadt.de/[/url]
- Lehrende: Reiner Anderl
Semester: ST 2020
Literatur
- Praktikumsanleitung (wird zu Beginn des Praktikums verteilt).
- Vorlesungsskript "Numerische Berechnungsverfahren" (im Sekretariat)
- M. Schäfer: "Numerik im Maschinenbau", Springer, Berlin, 1999
- M. Schäfer: "Computational Engineering", Springer, Berlin, 2006
- Praktikumsanleitung (wird zu Beginn des Praktikums verteilt).
- Vorlesungsskript "Numerische Berechnungsverfahren" (im Sekretariat)
- M. Schäfer: "Numerik im Maschinenbau", Springer, Berlin, 1999
- M. Schäfer: "Computational Engineering", Springer, Berlin, 2006
- Lehrende: Michael Schäfer
Semester: ST 2020